
3.3 Using the Network Wizard from within SETUP (Microsoft NT 4.0)
------------------------------------------------------------------
Note: Make sure ISA Express Adapters are put in Non-PnP mode before driver
      installation under Windows NT 4.0.  Also have the workstation Address
      from the AS/400 Administrator before continuing.  Lastly, have the
      Operating System diskettes/cdroms available.

WARNING: These install instructions assume NT Networking has been installed
         prior to beginning driver installation. Refer to the Windows NT System
         Administrator for details.

The "Network" wizard in Microsoft NT 4.0 is used to install the adapter
and to configure TCP/IP to use the IBM 5250 Express Adapters.  Setup will
always start the wizard with the correct tab selected for the task it is
performing.

Adding the IBM 5250 Express Adapter Software
---------------------------------------------

Step #1. If the IBM 5250 Express Adapter does not appear as an installed
-------- adapter under the "Adapter" tab, click on the "Add..." button.

Step #2. When the "Select Network Adapter" dialog box appears, click on
-------- the "Have Disk..." button.

Step #3. When the "Insert Disk" dialog box appears and press ok, select the
-------- item that reads "IBM 5250 Express TCP/IP" and then click on the "OK"
         button.

         NOTE: At this time Setup will copy files from the floppy to
               the Windows NT system directories.

Step #4. At this time a dialog box "IBM 5250 Express TCP/IP" will
-------  prompt the User for the Adapter type, choose the correct adapter
         installed in the User's Computer.  The following are the choices:

         IBM 5250 Express ISA Adapter (non-PnP)
         IBM 5250 Express PCI Adapter
         IBM 5250 Express PC Card


Step #5. After the correct adapter has been chosen click on "Configure"
-------  button.  At this time workstation Address must be obtained from
         the AS/400 Administrator.   All other adapter settings should
         default for the User's adapter type.

         After the proper workstation Address is input, click on "OK", then
         "SAVE" button.  This will save current 5250 Adapter settings.


Step #6. Now go to the Protocols folder tab under "Network" window.
-------  If TCP/IP is installed goto STEP #7, else continue.
         If TCP/IP is not in the Network Protocols window, it must be added.
         Choose the "Add" button then select TCP/IP Protocol then
         click on "OK".

        Note: At this time a dialog box "TCP/IP Setup" window will appear.
              This panel will ask if a DHCP Server is on the network.  The
              User must choose "YES" button to configure TCP/IP protocol.
              Refer to AS/400 System Administrator for non-DHCP configurations.

        WARNING: REMEMBER to choose "YES" button!!!!

        Windows NT may prompt User for Operating System diskettes/cdroms
        to complete Protocol setup.

        Now proceed to STEP #8.

Step #7. The User is here because TCP/IP is installed.  The User must check
-------  to see if DHCP is enabled on Client.  To verify this, from the
         "Network" dialog box and the "Protocols" tab folder, highlight the
          TCP/IP protocol and then click on the "Properties" button.

         The User should be in the "IP Address" folder tab.  Under
         "Adapter" pull down list and choose 'IBM 5250 Express Adapter'.
         Click on RADIO button "Obtain an IP address from DHCP server".

        Note: At this time a dialog box "TCP/IP Setup" window will appear.
              This panel will prompt for an existing DHCP Server is on the
              network.  The User must choose "YES" button to properly configure
              the 5250 TCP/IP protocol. Refer to the Windows NT User
              Administrator for non DHCP configurations.

        WARNING: REMEMBER to choose "YES" button!!!!

        Now it is time to close "Microsoft TCP/IP Properties" windows
        by clicking on "OK" button.

        Now proceed to STEP #8

Step #8. Close the Network Dialog box by clicking on "Close" button.
--------
       -----------  -----------  -----------
       | WARNING |  | WARNING |  | WARNING |
       -----------  -----------  -----------
       Windows NT will pop-up a "Network Settings Change" Dialog Box and ask
       the User to RESTART the computer.  DO NOT CLICK on "YES"!!
       Click on the "NO" Button!!!!  This will allow the SETUP
       program to complete the installation program.


Step #9. Follow the SETUP program prompts to completion. On completion,
-------  remove disk, then SHUTDOWN/RESTART the computer.  A successful
         driver installation will have the computer BEEP 3 TIMES
         indicating that TCP/IP communication has been established with
         the AS/400 Host.  If there are any problems refer to the
         "User Guide" in IBM 5250 Express TCP/IP program group.


