SN54ABT18245A, SN74ABT18245A SCAN TEST DEVICES WITH 18-BIT BUS TRANSCEIVERS

SCBS110G - AUGUST 1992 - REVISED DECEMBER 1996

Please be aware that an important notice concerningavailability, standard warranty, and use in critical applications ofTexasInstruments semiconductor products and disclaimers theretoappears at the end of this data sheet.

features

• Members of the Texas Instruments SCOPE^TM Family of Testability Products
• Members of the Texas Instruments Widebus^TM Family
• Compatible With the IEEE Standard 1149.1-1990 (JTAG) Test Access Port and Boundary-Scan Architecture
• SCOPE^TM Instruction Set
  • IEEE Standard 1149.1-1990 Required Instructions, CLAMP and HIGHZ
  • Parallel-Signature Analysis at Inputs
  • Pseudo-Random Pattern Generation From Outputs
  • Sample Inputs/Toggle Outputs
  • Binary Count From Outputs
  • Device Identification
  • Even-Parity Opcodes
• State-of-the-Art EPIC-IIB^TM BiCMOS Design Significantly Reduces Power Dissipation
• Packaged in Plastic Shrink Small-Outline (DL) and Thin Shrink Small-Outline (DGG) Packages and 380-mil Fine-Pitch Ceramic Flat (WD) Packages

SCOPE, Widebus, and EPIC-IIB are trademarks of TexasInstruments Incorporated.

description

The 'ABT18245A scan test devices with 18-bit bus transceivers aremembers of the Texas Instruments SCOPE^TM testabilityintegrated-circuit family. This family of devices supports IEEEStandard 1149.1-1990 boundary scan to facilitate testing of complexcircuit-board assemblies. Scan access to the test circuitry isaccomplished via the 4-wire test access port (TAP) interface.

In the normal mode, these devices are 18-bit noninverting bustransceivers. They can be used either as two 9-bit transceivers orone 18-bit transceiver. The test circuitry can be activated by theTAP to take snapshot samples of the data appearing at the device pinsor to perform a self test on the boundary-test cells. Activating theTAP in the normal mode does not affect the functional operation ofthe SCOPE^TM bus transceivers.

Data flow is controlled by the direction-control (DIR) andoutput-enable () inputs. Datatransmission is allowed from the A bus to the B bus or from the B busto the A bus, depending on the logic level at DIR. can be used to disable the deviceso that the buses are effectively isolated.

In the test mode, the normal operation of the SCOPE^TMbus transceivers is inhibited and the test circuitry is enabled toobserve and control the input/output (I/O) boundary of the device.When enabled, the test circuitry performs boundary-scan testoperations according to the protocol described in IEEE Standard1149.1-1990.

Four dedicated test pins observe and control the operation of thetest circuitry: test data input (TDI), test data output (TDO), testmode select (TMS), and test clock (TCK). Additionally, the testcircuitry performs other testing functions such as parallel-signatureanalysis (PSA) on data inputs and pseudo-random pattern generation(PRPG) from data outputs. All testing and scan operations aresynchronized to the TAP interface.

The SN74ABT18245A is available in TI's shrink small-outline (DL)and thin shrink small-outline (DGG) packages, which provide twice theI/O pin count and functionality of standard small-outline packages inthe same printed-circuit-board area.

The SN54ABT18245A is characterized for operation over the fullmilitary temperature range of -55°C to 125°C. TheSN74ABT18245A is characterized for operation from -40°C to85°C.

View more information about generic part numbers:SN54ABT18245A, SN74ABT18245A

Go to the Engineering Design Center to locate information on other TI Semiconductor devices.

(c) Copyright 1998 Texas Instruments Incorporated. All rights reserved.
Trademarks, Important Notice!