SN54ABT16500B, SN74ABT16500B 18-BIT UNIVERSAL BUS TRANSCEIVERS WITH 3-STATE OUTPUTS

SCBS057G - DECEMBER 1990 - REVISED MAY 1997

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of TexasInstruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

features

Members of the Texas Instruments Widebus^TM Family
State-of-the-Art EPIC-IIB^TM BiCMOS Design Significantly Reduces Power Dissipation
UBT^TM (Universal Bus Transceiver) Combines D-Type Latches and D-Type Flip-Flops for Operation in Transparent, Latched, or Clocked Mode
ESD Protection Exceeds 2000 V Per MIL-STD-883, Method 3015
Latch-Up Performance Exceeds 500 mA Per JEDEC Standard JESD-17
Typical V_OLP (Output Ground Bounce) < 0.8 V at V_CC = 5 V, T_A = 25°C
High-Impedance State During Power Up and Power Down
Flow-Through Architecture Optimizes PCB Layout
Package Options Include Plastic 300-mil Shrink Small-Outline (DL) and Thin Shrink Small-Outline (DGG) Packages and 380-mil Fine-Pitch Ceramic Flat (WD) Package Using 25-mil Center-to-Center Spacings

Widebus, EPIC-IIB, and UBT are trademarks of Texas Instruments Incorporated.

description

These 18-bit universal bus transceivers combine D-type latches and D-type flip-flops to allow data flow in transparent, latched, and clocked modes.

Data flow in each direction is controlled by output-enable (OEAB and OEBA\), latch-enable (LEAB and LEBA), and clock (CLKAB\ and CLKBA\) inputs. For A-to-B data flow, the device operates in the transparent mode when LEAB is high. When LEAB is low, the A data is latched if CLKAB\ is held at a high or low logic level. If LEAB is low, the A data is stored in the latch/flip-flop on the high-to-low transition of CLKAB\. OEAB is active-high. When OEAB is high, the outputs are active. When OEAB is low, the outputs are in the high-impedance state.

Data flow for B to A is similar to that of A to B but uses OEBA\, LEBA, and CLKBA\. The output enables are complementary (OEAB is active high and OEBA\ is active low).

When V_CC is between 0 and 2.1 V, the device is in the high-impedance state during power up or power down. However, to ensure the high-impedance state above 2.1 V, OE\ should be tied to V_CC through a pullup resistor and OE should be tied to GND through a pulldown resistor; the minimum value of the resistor is determined by the current-sinking/current-sourcing capability of the driver.

The SN54ABT16500B is characterized for operation over the full military temperature range of -55°C to 125°C. The SN74ABT16500B is characterized for operation from -40°C to 85°C.

Title: 18-BIT UNIVERSAL BUS TRANSCEIVERS WITH 3-STATE OUTPUTS
Product Family: UNIVERSAL BUS TRANSCEIVERS (UBTS)
Device Functionality: 18-BIT BUS TRANSCEIVER
Orderable Devices: SN74ABT16500BDGGR, SN74ABT16500BDL, SN74ABT16500BDLR

View the complete PDF datasheet: scbs057g.pdf (141 K Bytes) (Requires Acrobat Reader 3.x)

View more information about generic part numbers:SN74ABT16500B

Go to the Engineering Design Center to locate information on other TI Semiconductor devices.